The online newspaper for the forest products industry including loggers, sawmills, remanufacturers and secondary wood processors.
 
Blade Adjustments Keep Mill Cutting True: ‘Swingmill’ Blade Adjustments Are Easy to Learn and Take Only a Few Minutes to Make

‘Swingmill’ Blades – Blade Adjustments Keep Mill Cutting True

By Staff
Date Posted: 7/1/2009


            (Editor’ Note: This is the fourth in a series of articles about saw blades for swing blade portable sawmills, also known as ‘swingmills.’ The articles are provided by Peterson Portable Sawmills.)

            Adjusting the blade so it cuts true is one of the most important aspects of running a swingblade portable sawmill.

            Adjustments make up about 70% of the training on a swingblade mill; there is very little else. Perfect blade adjustments will make it real easy to saw a mountain of timber. By contrast, bad blade adjustments can make your day a struggle and cost you money on frequent re-tensioning.

            Thankfully, the adjustments are simple to learn and take only a few minutes to tweak. And unless you’ve changed your mill spec, jarred it while moving or bent something while strapping your mill on the truck, you should not have to make blade adjustments very often at all. Some millers adjust the blade once and never do it again if they are on a fixed site.

            Good manufacturers will test the mill and set the adjustments at the factory prior to shipping. However, rough handling in transit can throw things out.

            When you first set up your mill, saw a few boards to get the feel of things first. If the blade adjustments are out for a couple days, you probably won’t damage anything because you’ll only be pushing it slowly and carefully being a ‘newbie.’ When you are comfortable with how the mills works and saws, start looking at the sawing patterns and taking note of the board results.

            There are four blade adjustments that are made by simple bolts or spacers on the mill. Test and adjust each one separately. Do not make two adjustments at once; it will confuse you.

            One of the most important things to look for is a crisscross pattern on the cut surfaces. Saw marks in both directions indicate a blade is adjusted true and parallel to the tracks. Cut marks in only one direction show the blade is slightly out of align; i.e., only one edge (the front or the back) is doing all the work.

 

Horizontal Blade Adjustments Horizontal Crisscross

            This front-and-back alignment prevents your blade from either nose-diving or rising as it travels forward in the horizontal (flat) position. Look at the sawing pattern on the face of the log. You should see sawing lines in both directions. If you see lines in only one direction, only the front or the back is cutting, and it’s probably diving or rising a bit, jamming, and even making tapered boards.

            Your swingmill will have adjustments to tilt the blade, or the unit it is contained in, up or down. Once you’ve done a little adjustment, cut another board to recheck. Inspect your crisscross pattern.

 

Lean-In

            Lean-in makes sure the right side of the blade is ever-so-slightly lower than the left side – 0.5mm or 1/32-inch. This is so that only the right side of the blade cuts into the timber as it moves across the log. You don’t want the back of the blade re-sawing; this will cause the blade to ‘climb-cut,’ which, besides being very dangerous, is hard to push forward and throws sawdust back at the operator. You need to see a little line on the log face between each wide board. If there is no line or it is quite a noticeable step, you will need to adjust the right side of the horizontal blade up or down a smidgen.

            Your swingmill will have a bolt that is adjustable to control the blade’s locked horizontal position. Saw another wide board to test before moving on.

 

Vertical Blade Adjustments Intersection

            Intersection or vertical depth is set to ensure the vertical and horizontal cuts meet in just the right place. A tiny ‘step’ on the corner of the sawn log where the last board just came off shows a perfect intersect. However, if your boards don’t come off at all, the vertical blade is too high and needs to be lowered. If there are grooves left in the log, the vertical blade is too low and needs to be raised.

            Turn the mill off and measure the distance between the bottom-most blade tip and the surface of the sawn log under it. This gap should be around 3mm or 1/8-inch. Measure again with a ruler after adjusting.

 

Crisscross

            This left-and-right alignment prevents your vertical blade from veering off to the left or tracking to the right as you pull it back through the log to complete the return cut. Out-of-alignment symptoms will include being hard to pull, heavy cut lines in one direction only, tapered boards, and even a ‘zinging’ sound as the blade exits the log.

            First, get the feel of pulling the mill when sawing to establish your pull points. Find the most comfortable method of pulling. Some people use the bar only, and some use the bar and the pull handle; some use the bar and the frame upright (for box frame mills). Different pull points will twist the mill slightly differently, changing the vertical blade direction a bit. So whatever you choose, stick to it for the majority of your milling.

            Now set your vertical blade adjustments to match your most common pulling style. Basically, the vertical blade needs to be parallel to the tracks while and considering you may be pulling a slight twist into the frame.

            The adjustment for this one may be on one of the corners of the sawing unit, where you will ‘twist’ the unit within its frame and hence the direction of the blade.

            Yes, you can change your pull locations later as needed for larger or smaller logs. The blade may resist a bit more when the frame is pulled at a slightly different angle.

 

Exceptions

            When your saw is just not cutting right, look for other obvious things first before rushing in to ‘adjust’ your blade. Are all the rollers on the same groove? Are the tracks square and parallel? Is the locking handle loose, allowing the head to move? Has one of the chains been stretched when transporting?

            Sometimes, log tension can make it still look like your blade adjustments are out when they are not. Logs with a lot of tension in them will pinch and twist the blade as it travels through a cut, giving you false sawing indicator patterns on the log. If it comes and goes, it could just be tension!

            The next article will look at blade running costs.

 




 






Do you want reprints or a copyright license for this article?   Click here


Research and connect with suppliers mentioned in this article using our FREE ZIP Online service.


© Copyright 2014, IndustrialReporting, Inc.
10244 Timber Ridge Dr., Ashland, VA 23005
Phone: (804) 550-0323 or FAX (804) 550-2181
Terms of Use     Contact our Staff